脱氧剂干燥剂包装膜打微孔机

时间：2025-12-21

Mini Redundant】DMRW-6350F 
    
   350W   
   
   Server,Storage System,IPC,Communication,Networking 
 
 
 
 
185.00x150.00x86.00  (mm)
7.28x5.91x3.39  (inch)  
 

VOLTAGE: DC-36V ~ -72V
INPUT CURRENT: 12.0A(RMS). FOR -48 VDC
INRUSH CURRENT: 20A MAX 
 
 
 
 
   
Output Voltage Output Current Min. Output Current Max. Output Current Peak Regulation Load Regulation Line Output Ripple & Noise Max.[P-P] 
+5V 3.0 32.00  ± 5% ± 1% 50mV 
 
  
-5V 0.1 0.5  ± 6% ± 1% 120mV 
 
  
+12V 2.5 25  +7 / -5 % ± 1% 120mV 
 
  
-12V 0.1 1.2  ± 10% ± 1% 150mV 
 
  
+3.3V 1.0 25  ± 5% ± 1% 50mV 
 
  
+5VSB 0.1 2  ± 5% ± 1% 50mV 
 
  
       
 
  
       
 
  
       
 
  
 

* TEMPERATURE RANGE : OPERATING 100C --- 400C 
* HUMIDITY:OPERATING:20%-95%, NON-OPERATING:10%-95%
* REMARKS:85% IS NORMAL CONDITION AND 95% IS WITH SPECIAL COATING PROCESS
* HOLD UP TIME: 1.6 ms MINIMUM AT FULL LOAD & NOMINAL INPUT VOLTAGE
* DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
* EFFICIENCY: 65% TYPICAL, AT FULL LOAD
* POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
* OVER LOAD PROTECTION: 130 ± 20%.
* OVER VOLTAGE PROTECTION: 
+5V → 5.5V ~ 7.0V, + 3.3V → 4.0V ~ 4.5V . SHORT CIRCUIT:5V,12V,3.3V
* EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
* SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950 * REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE / ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY), AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE, AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABED 
* COOLING : TWO 40 mm DC FANS (MODULE)
* AC INLET IN EACH MODULE

词条
词条说明
复合机分切机增添薄膜打孔装置
复合机分切机增添打孔装置：塑料包装薄膜经该打孔装置打孔，打孔针辊精度高，孔间距及孔径大小均匀，针尖高度一致,孔径大小(自行调整)及孔型排列、不同薄膜材料打孔需求按客户所需定制。该打孔薄膜广泛应用于面包、食品、鲜花、护垫透气打孔、包装薄膜多功能打孔分切一体机、干燥剂包装、脱氧剂包装打孔等包装薄膜及工业上打孔透气产品,覆盖多行业的薄膜打孔领域。该打孔加热针辊模具总成装置直接安装在塑料膜分切机(分条机
脱氧剂干燥剂包装膜打微孔机
脱氧剂干燥剂包装膜打微孔机,塑料包装薄膜经该打孔装置打孔，打孔针辊精度高，孔间距及孔径大小均匀，针尖高度一致,孔径大小(自行调整)及孔型排列、不同薄膜材料打孔需求按客户所需定制。该打孔薄膜广泛应用于面包、食品、鲜花、护垫透气打孔、热暖包膜透气打孔机、干燥剂包装、脱氧剂包装打孔等包装薄膜及工业上打孔透气产品,覆盖多行业的薄膜打孔领域。该打孔加热针辊模具总成装置直接安装在塑料膜分切机(分条机)、吹膜机
泉州市鲤城区翔飞机械厂
泉州市鲤城区翔飞机械厂秉承“顾客至上，锐意进取,专注专业、精益求精”的经营理念，坚持“客户**”的原则,本着“诚信为本，品质**”为广大客户提供优质的塑料包装薄膜打孔机.塑料薄膜打孔针辊等机械设备。
吹膜机分切机增添打孔装置
吹膜机分切机增添打孔装置：塑料包装薄膜经该机械设备打孔，打孔针辊精度高，孔间距及孔径大小均匀，针尖高度一致,孔径大小(自行调整)及孔型排列、不同薄膜材料打孔需求按客户所需定制。该打孔薄膜广泛应用于面包、食品、鲜花、医疗美容、干燥剂包装等包装薄膜及工业上打孔透气产品,覆盖多行业的薄膜打孔领域。该打孔加热针辊模具总成装置直接安装在塑料膜分切机(分条机)、吹膜机,复合机,印刷机等产品需打孔的原机械设备